Quick connectors like the # BDW20348 do come in different sizes depending on the gauge of wiring required for the application. There are a couple of different options for 2-4 gauge wiring that you can use that I've listed below for you to check out. The connectors in the # BDW20348 are much larger than these other options.
Bulldog Winch Rear Wiring Kit - Quick Connect to Terminal End - 2 Gauge - 20' Long # BDW20206
Bulldog Winch Rear Wiring Kit - Quick Connect to Terminal End - 3 Gauge... view full answer...
Sure do!
According to my friend in the Tech Services department at Tekonsha, their # TK93VR brake controller wiring harness is compatible with the 2021 Jeep Grand Cherokee. The connector that the harness plugs into is located near the top of the e-brake pedal. I've linked to an install video that should help you locate the connector. view full answer...
A bolt-on axle over-under kit like # K71-384-00 and # K71-385-00 will typically give your trailer between 4 and 5-inches of lift. The exact amount of lift depends on the axle diameter and the height of the leaf spring stack. Lift will be the sum of the axle diameter plus the height of the spring stack. Kit # K71-385-00 works for axles with 3-inch diameter
Installing an axle over-under lift kit on a trailer is not a complex job but it does require the right safety equipment to avoid risk... view full answer...
The wiring harness I recommend for your tow bar to flat tow a 2015 Jeep Grand Cherokee is the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit # RM-15267. This diode kit allows you to use your vehicle's tail lights and wiring system while preventing feedback from your RV that might damage the electrical systems. This kit wires 2-wire and 3-wire systems to operate as a combined lighting systems, so your RV and Jeep Grand Cherokee's lights will work in conjunction.
I've linked a quick... view full answer...
It doesn't look like the picture came though, however they do not make the PRO TRAXX 5" nerf bars for your 2012 Jeep Grand Cherokee.
The closest I was able to match style wise is the Westin Oval Tube Steps w/ Custom Installation Kit # 22-5055-1985 which would use the Custom Installation Kit for Westin Oval and Premier Oval Tube Steps # 22-1985.
If you can get some more info on your steps, I'd be happy to find a proper set of mounting hardware. view full answer...
If your Grand Cherokee has the factory 7-way at the back bumper, it'll be prewired for a brake controller. You'll need the # TK93VR wiring harness and the # 331-TPH-017 adapter. The # TK93VR harness will plug into the factory connector located under the dash to the left of the steering column, above where the driver's left knee would be. The # 331-TPH-017 adapter plugs into the harness, the other end plugs into the controller.
If your Grand Cherokee does NOT have the factory 7-way, you'll... view full answer...
The Tekonsha Primus IQ Trailer Brake Controller TK90160 can definitely be installed on your 2020 Jeep Grand Cherokee, you just need the following wiring parts depending on if you have the factory tow package or not:
With Factory Tow Package
- Plug-In Wiring Adapter # TK93VR
Without Factory Tow Package
- Curt 4-Way Wiring Kit # C62VR
- Universal Installation Kit # ETBC7
- No-Drill Mount Bracket # 18136
If you have the factory tow package you'll have a connector located underneath... view full answer...
I was able to do some research and find that the 2021 Jeep Grand Cherokee and 2020 Jeep Grand Cherokee have the same plug and play connector for a brake controller, so you'll be able to use the Redarc Tow-Pro Elite Trailer Brake Controller - 1 to 3 Axles - Proportional # RED44FR you were looking at. This controller is a great solution and one of the most popular proportional controllers on the market-especially with users who take their trailers off-road, since it provides fully customizable... view full answer...
To use the Roadmaster BrakeMaster system # RM-9160 on your 2014 Jeep Grand Cherokee Overland, you will need the following items:
Stop Light Switch kit, # RM-751449
Seat Adapter, # RM-88287
Because your Grand Cherokee has a combined lighting system (the brake lights and turn signals are on the same circuit) you should not need a brake light relay. view full answer...
Yes, The Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136 can be powered by using your lithium batteries so you can boondock. We would not know how much power it would draw off the battery though.
This system with automatically extend and retract which allows for a hands-free operation while jack lifts and lowers. The leveling system has a sturdy steel construction and has a black powder coat finish that helps resist corrosion. This application will... view full answer...
For the correct plug-and-play wiring harness to go with the Curt Spectrum Trailer Brake Controller # C51170 on your 2018 Jeep Grand Cherokee with a 7-way and tow package, that is the Curt Custom Wiring Adapter for Trailer Brake Controllers # C51446. With this adapter, you will be able to simply plug in the Spectrum wiring right into the port under your dash for easy installation. view full answer...
Not a problem at all!
As long as your motorhome has a trailer hitch on the rear, then you can absolutely attach a bike rack to it.
If you do not have one currently installed, we have the Adjustable Width Trailer Hitch Receiver for RVs # C13702 which will fit trailers with a frame width of 18" to 51" wide,
Or
We also have the Adjustable Width Trailer Hitch Receiver for RVs # 13703 which will fit trailers with a frame width of 22" to 72" wide.
From here, I recommend going with the Lets... view full answer...
A complete flat towing setup consists of base plates, a tow bar, safety cables, tow bar wiring, supplemental braking and potentially a high/low adapter, and I can help you find all of those parts and get you on the road with your 2021 Jeep Grand Cherokee in tow.
For base plates I recommend using the Roadmaster Direct-Connect Base Plate Kit - Removable Arms # RM-521440-5 because of the quality of Roadmaster towing components. These base plates come with removable arms that will keep your... view full answer...
Yes, I do have a wiring harness for your 2021 Jeep Grand Cherokee without a tow package. You need the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # 118727. This custom-fit T-One connector plugs into your Cherokee's wiring harness behind the rear tail lights. This harness will give you a 4-flat connector that will allow you to control your trailer's lighting functions. view full answer...
I looked up the owners manual for your 2020 Jeep Grand Cherokee. According to the manual the only model that can be flat towed (recreational towing) is the 4 wheel drive model with 4-LO range. As long as that is the model that you have then you will need the following items to flat tow your vehicle.
Base Plate Kit:
I recommend the Roadmaster Direct-Connect Base Plate Kit # RM-521440-5. This base plate is made in the USA and has clean streamlined look, along with a limited lifetime warranty.... view full answer...
Since you don't have the trailer towing package on your 2013 Jeep Grand Cherokee you do need to start off by installing a 4-Way connector. I recommend the Tekonsha T-One # 118425 as we have found Tekonsha to be one of the most reliable wiring companies that we carry.
To have 7-Way and 4-Way connectors on your Jeep you also need the Universal Wiring Kit # ETBC7. This connects to the T-One and give you both connections that you need. It also includes everything you need for the 7-Way to... view full answer...
The longest ball mount we carry to fit a Class II, 1-1/4 inch hitch receiver is the Curt # C45000. It's 13-1/2 inches from the hitch pin hole to the ball hole. However, it only provides 3-7/8 inches of rise and cannot be used in the drop position. Much less than the Brophy # BM96 you have. It does have the same 3/4 inch ball hole diameter as the Brophy.
Another option that may work is the Curt # C45015 that's 11-5/8 inches long. It can't be used in the drop position either but does... view full answer...
In order to successfully flat-tow your 2014 Jeep Grand Cherokee Trailhawk you are going to need a few additional parts outside of the Blue Ox Base Plate Kit part # BX1128 and the M&G Supplemental Braking System. I have listed these parts for you below:
Blue Ox Alpha 2 Tow Bar part # BX7380
Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit part # RM-15267
Roadmaster Stop Light Switch Kit part # RM-751449
The stop light switch kit listed above is a requirement for proper usage with... view full answer...
I did a bit of research and the 1996 Jeep Grand Cherokee can be towed 4 wheels down, but you will need a drive shaft coupling to allow the wheels to rotate freely. You should always check your owners manual or with the vehicle dealer for complete instructions for towing your vehicle.
Once you have a drive shaft coupling installed you will need to install either the Roadmaster Classic Base Plate Kit with Fixed Arms, item # 1411-1, or the Roadmaster XL Base Plate Kit with Removable Arms,... view full answer...
If you have no factory wiring or aftermarket wiring already installed on your 2001 Jeep Grand Cherokee you will need a Curt T-Connector Vehicle Wiring Harness # C55369 to connect to the factory wiring connector that is installed on every 2001 Jeep Grand Cherokee. This will control the tail light functions as well as the running lights of your 7-way.
The Universal Installation Kit for Trailer Brake Controller # ETBC7 will provide you with a 7-way, the wiring and connectors to run a power... view full answer...
Go To Results